Showing posts with label Curtain Walls. Show all posts
Showing posts with label Curtain Walls. Show all posts

Thursday, December 05, 2013

Curtain Walls and Doors

This is an echo from 2012, not that old but a situation that frequently frustrates new users.

There are two situations that trip up new users when it comes to doors. I wrote about about one of these Reviteristics in April 2010. That post is about Openings and this one is about curtain wall panel doors.

When people first make a curtain wall that is supposed to get a door they quite naturally assume the door tool is the right place to start. Wrong. Curtain walls are special and they are made up of curtain grids, panels and mullions. A curtain wall door is really a curtain wall panel. They are a panel because Revit needs to keep their width and height flexible, to accommodate any changes we might make. A regular door family can vary in size but it can't respond to curtain grids being moved. We can't even put a regular door in a curtain wall. That's not entirely true but I'd have to get into yet another Reviteristic, using other wall types as curtain wall panels.

We need to understand that a door in a curtain wall isn't a "door", at least not to the Door tool. To make matters a bit more confusing Revit treats this curtain wall panel, pretending to be a door, as a door in schedules and in Visibility/Graphics.

    It would be better if we could click on the Door tool and have the option to place a "regular" door or a "curtain panel" door. At least this way it would become immediately apparent that there is a difference!

Curtain wall panel doors are found in the Doors folder within the content library. That seems slightly logical, in the same way that Opening families are found there. When we want to load a curtain wall door family, browse to the door library (stock content location).

Placing a curtain wall door is a bit different than a regular door in a wall. We don't use the Door tool. We have to swap out the panel that should be a door with the curtain wall door family that you loaded. To do this we need to use the TAB key to select the panel and then use the Type Selector to choose the curtain wall door family instead.

Once you do this you'll have to make sure that the curtain grids and mullions are adjusted to report the desired size. If you set the grids and mullions before the door is in place you'll find that the size is not quite the clean numbers you probably wanted. You can resolve this with mullions that use different offset values or just re-position the curtain grids until you get a cleaner door size.

I captured another video in the "Five Minutes with..." theme.

If you want to create a new curtain wall door family you ought to examine and/or reverse engineer the stock one first. You can start from scratch with the family template (Door - Curtain Wall.rft)

Wednesday, December 04, 2013

Curved Curtain Wall Edges

This is an echo of my post from October 2011.

I recently responded to a post at RevitForum.org when a member asked about creating what sounded to me like a round top window using a curtain wall. I posted a couple screen captures and briefly discussed how they were made. This first one is a curtain wall embedded in a host wall followed by using Edit Profile to alter the sketch of the curtain.


This one is a bit more involved. I started with a single rectangular curtain wall and copied it to clipboard. Then I used Edit Profile to change it's shape. I then used Paste Aligned > Same Place to put the original curtain wall back on top of the first one. Using Edit Profile again allowed me to follow the edge of the first and design the second wall. Repeat the steps for the third and we have a curving set of mullions that are defined by three curtain walls that have complimentary sketches defined using Edit Profile.


I mentioned the use of the parameter Automatically Embed, a feature of curtain wall. The curtain wall types that are present in the stock templates vary but the simplest ones like Curtain Wall1 don't have the feature selected. If you sketch one of these walls over the top of another you'll get an error message.


I posted the following image because I thought it was worthwhile mentioning that the Cut Geometry tool the warning message references allows us do things like this too.


I also created a video that discusses these concepts.

Monday, December 02, 2013

Louver Curtain Wall Panel

This short video discusses a technique using a curtain wall's type parameters to create a flexible louver panel. It gets the idea of a louver across and it doesn't involve using the family editor or arrays. It remains the most watched video I've posted over the years so while I'm at AU this week I decided to "bump" it again.


Monday, April 02, 2012

The Missing Door

There are two situations that trip up new users when it comes to doors. I wrote about about one of these Reviteristics in April 2010. That post is about Openings and this one is about curtain wall panel doors.

When people first make a curtain wall that is supposed to get a door they quite naturally assume the door tool is the right place to start. Wrong. Curtain walls are special and they are made up of curtain grids, panels and mullions. A curtain wall door is really a curtain wall panel. They are a panel because Revit needs to keep their width and height flexible, to accommodate any changes we might make. A regular door family can vary in size but it can't respond to curtain grids being moved. We can't even put a regular door in a curtain wall. That's not entirely true but I'd have to get into yet another Reviteristic, using other wall types as curtain wall panels.

We need to understand that a door in a curtain wall isn't a "door", at least not to the Door tool. To make matters a bit more confusing Revit treats this curtain wall panel, pretending to be a door, as a door in schedules and in Visibility/Graphics.

    It would be better if we could click on the Door tool and have the option to place a "regular" door or a "curtain panel" door. At least this way it would become immediately apparent that there is a difference!

Curtain wall panel doors are found in the Doors folder within the content library. That seems slightly logical, in the same way that Opening families are found there (Edit: Openings have their own folder beginning with version 2012). When we want to load a curtain wall door family, browse to the door library (stock content location).

Placing a curtain wall door is a bit different than a regular door in a wall. We don't use the Door tool. We have to swap out the panel that should be a door with the curtain wall door family that you loaded. To do this we need to use the TAB key to select the panel and then use the Type Selector to choose the curtain wall door family instead.

Once you do this you'll have to make sure that the curtain grids and mullions are adjusted to report the desired size. If you set the grids and mullions before the door is in place you'll find that the size is not quite the clean numbers you probably wanted. You can resolve this with mullions that use different offset values or just re-position the curtain grids until you get a cleaner door size.

I captured another video in the "Five Minutes with..." theme.

If you want to create a new curtain wall door family you ought to examine and/or reverse engineer the stock one first. You can start from scratch with the family template (Door - Curtain Wall.rft)

Monday, October 31, 2011

Using Edit Profile on a Curtain Wall

I recently responded to a post at RevitForum.org when a member asked about creating what sounded to me like a round top window using a curtain wall. I posted a couple screen captures and briefly discussed how they were made. This first one is a curtain wall embedded in a host wall followed by using Edit Profile to alter the sketch of the curtain.


This one is a bit more involved. I started with a single rectangular curtain wall and copied it to clipboard. Then I used Edit Profile to change it's shape. I then used Paste Aligned > Same Place to put the original curtain wall back on top of the first one. Using Edit Profile again allowed me to follow the edge of the first and design the second wall. Repeat the steps for the third and we have a curving set of mullions that are defined by three curtain walls that have complimentary sketches defined using Edit Profile.


I mentioned the use of the parameter Automatically Embed, a feature of curtain wall. The curtain wall types that are present in the stock templates vary but the simplest ones like Curtain Wall1 don't have the feature selected. If you sketch one of these walls over the top of another you'll get an error message.


I posted the following image because I thought it was worthwhile mentioning that the Cut Geometry tool the warning message references allows us do things like this too.


I also created a video that discusses these concepts.



Wednesday, August 17, 2011

Curtain Wall Panel - Edit in Place

You can edit a system panel in place. Yes that means you can select a curtain wall's system panel like Glass or Solid and then Edit-in-Place. Do you have a quirky design situation somewhere on your curtain wall and want to just make the change right there without creating a new panel family and loading and swapping? You can!

  • Select the panel (unpin if defined by the CW type)
  • Click Edit in Place




  • You'll find you are in Sketch Mode
  • Select and edit the solid form for glass/solid or
  • Create another form/void to design the custom panel
  • Assign Sub-category(ies)
  • Assign Material(s)
  • Finish the modelling
  • Finish the in-place editing

et Voila!


Not the right solution for multiple versions of this but when one (or a few) is all you are dealing with, not bad?!


Thursday, July 14, 2011

The Difference Between Join and Attach

There are two kind of messages that Revit shows you regarding how walls, floors and roofs interact.

The first kind (Attach) occurs when the geometry of a wall touches a floor or passes through the floor. If you edit the sketch of a floor, when you finish the sketch Revit asks you if you'd like to attach this wall (or any other walls that intersect too) to the underside of the floor.


The point of this is to establish an "automatic" relationship between the underside of a floor and various walls. If the floor type (thickness) changes the top of the wall(s) will change as well. If the level the floor is assigned to is raised/lowered the walls adjust accordingly too. It's meant to be "quicker" than manually doing it yourself by selecting walls and using the Attach Top/Base tool. However you may want some walls to do it and others not so much. Many times the "correct" answer is NO.

Here are the results for yes and no responses (note that there is no "joining" of geometry, just the wall height is changed).


Same thing happens when a wall and roof geometry intersects except the dialog message is slightly different.


The second kind (Join) is when a floor intersects a wall, like at exterior walls. Revit asks if you want to join geometry so the cut/projection lines that it draws better represent how these elements would really intersect.


The first message does appear too, just before the second message appears. It's good to choose NO to the first so the wall does not get attached (which would change its height) and then YES so the geometry joins nicely. If you aren't cutting a section through this part of the building then you could argue there is no need to join geometry since nobody will see the clumsy connection between wall and floor.


Now for this message to appear it is necessary to "Pick Walls" and use the "Extend into wall (to core)" Option. If you don't use these then you just get the first message.


If you choose NO for both "questions" you can always use the Join Geometry tool later between any elements that need to "clean up" better. Again the point of this second kind of question is to provide a "speedier" way to end up with a better section(s) when you cut one later.

Monday, October 12, 2009

Curtain Wall - Corner Butt Glazing Condition

I received an email from a client today asking about this situation and I thought it was a good opportunity to see if my voice would hold up for a brief video. I've been trying to shake a throat focused "cold" for a couple weeks now. Working through it hasn't helped clear it up.

I posted the new video about this HERE.

The essence of the tip is to create your own butt glazing "mullion" to stand in for the glazing compound that would really be there. You can duplicate the stock 5"x 5" Corner Mullion type, provide a new Offset parameter, define the Material as Glass, Match the left and right corner panel dimensions in the Depth 1 and Depth 2 parameters.

You place this mullion type at the corner of two curtain walls and you'll end up with something like this image.


If you want to, you can listen and watch right here below now.


Sunday, September 13, 2009

Curtain Wall Louvers or How to Avoid Arrays

I think that Phil Read is the first person I saw reveal this technique many years ago now, probably at Autodesk University but it may have been at AUGI in a thread, I just don't remember now.


The essence of this tip is using a curtain wall type to define a series of mullions that pose as louvers. The special curtain wall type is then swapped out for other panels in a larger host curtain wall. The mullions are defined as new types as well, one for a louver and one for the perimeter framing if necessary. It is important to use the Empty Panel for the Default Panel parameter so that there are no panels in the louver curtain wall, just mullions. I posted a VIDEO and you can listen and watch here now if you prefer.



Monday, September 22, 2008

Curtain Walls - Fun Stuff by Other Bloggers

It is considered ill form to just blog about stuff other bloggers are saying or doing but in this case I don't care! I find the stuff that people "cook up" in Revit to be interesting and I'm motivated to call attention to these three, two "Dave's" and a Craig.

Craig started it all with his POST at iRevit.

His inspiration was:

I recently attended a panel discussion at Siggraph 2008, where Enrique Rosado discussed his work with Viennese Sculptor Erwin Hauer. Hauer explored continuous perforated modular structures that as architectural panels, expanded into infinite surfaces with escher-esque qualities.

David Baldacchino picked up the ball with his POST at Do u Revit?
David Light then picked up the ball and ran with his POST at his Revit blog.
Then he ran a bit more with this POST.

Check out their posts and see what inspiration they provide? If me just writing about them doesn't inspire you to visit their blogs then does this little collage do it for you?